Testbook Logo
Exams SuperCoaching Test Series Skill Academy
More

Question

Download Solution PDF

The efficiency of an LED for generating light is directly proportional to the

This question was previously asked in
ESE Electronics 2012 Paper 1: Official Paper
Attempt Online
View all UPSC IES Papers >
  1. applied voltage
  2. current injected
  3. temperature
  4. level of doping. 

Answer (Detailed Solution Below)

Option 2 : current injected
Free Tests
View all Free tests >
Free
ST 1: UPSC ESE (IES) Civil - Building Materials
6.1 K Users
20 Questions 40 Marks 24 Mins
Start Now

Detailed Solution

Download Solution PDF
  • The efficiency of LEDs will be determined by the radiate recombination rate
  • Temperature influence the output power of an LED through its effects on the internal quantum efficiency of the device. 
  • The internal quantum efficiency of LEDs decreasing exponentially with increasing temperature. 
  • The efficiency of LED is directly proportional to the current injected. 
Download Solution PDF
Latest UPSC IES Updates

Last updated on May 28, 2025

->  UPSC ESE admit card 2025 for the prelims exam has been released. 

-> The UPSC IES Prelims 2025 will be held on 8th June 2025.

-> The selection process includes a Prelims and a Mains Examination, followed by a Personality Test/Interview.

-> Candidates should attempt the UPSC IES mock tests to increase their efficiency. The UPSC IES previous year papers can be downloaded here.

More LED Questions

Q1.The light-emitting diode (LED) is made of
Q2.As the colour varies, forward voltage varies, in:
Q3.Which component in a TV is responsible for generating the high voltage sawtooth signals at a relatively high frequency?
Q4.An LED has lower output power, ________ switching speed and _______ spectral width than the LASER as an optical source.
Q5.The semiconductor material NOT used in LED is:
Q6.Study the given figures. Identify the elements from 1 to 4 and select the option that shows their correct names
Q7.What is the typical range of the forward voltage of an LED?
Q8.The value of current limiting resistor for a stack of 4 LED's connected in series will be ______ if the LED's are 3 V, 3 mA and DC source is 15 V.
Q9.The efficiency of an LED for generating light is directly proportional to the
Q10.An LED made using GaP emits radiation in _______.

More Optical Sources and Detector Questions

Q1.The light-emitting diode (LED) is made of
Q2.By considering standard notations, the line width of the spontaneous emission is approximately
Q3._______ is used to detect the optical signal.
Q4.As the colour varies, forward voltage varies, in:
Q5.Which component in a TV is responsible for generating the high voltage sawtooth signals at a relatively high frequency?
Q6.Which of the following statements are correct? A. A multiplier can be used as a balanced demodulator or detector. B. Dynamic range compression is the process of reducing the peak‐to‐peak variation of a signal to a lower range. C. An antilogarithmic amplifier is useful for dynamic range compression. D. In a phase‐locked loop circuit, the capture range is always larger than the lock range.  Choose the correct answer from the options given below:
Q7.An LED has lower output power, ________ switching speed and _______ spectral width than the LASER as an optical source.
Q8.The quantum efficiency η for the photodetector is - Where Iph = average photo current Po = Average incident optical power hc/λ = incident photon energy
Q9.Measurement of optical absorption of a solution is disturbed by the additional stray light falling at the photo-detector. For estimation of the error caused by stray light the following data could be obtained from controlled experiments. Photo-detector output without solution and without stray light is 500 μW. Photo-detector output without solution and with stray light is 600 μW. Photo-detector output with solution and with stray light is 200 μW. The percent error in computing absorption coefficient due to stray light is
Q10.Which of the following is used in the specification of optical detectors?
Crack GATE Electrical with
India's Super Teachers
Explore Supercoaching For FREE
Suggested Test Series
View All >
UPSC ESE (IES) Civil Mock Test Series
116 Total Tests with 1 Free Tests
Start Free Test
UPSC ESE (IES) Prelims Paper 1 Mock Test Series
54 Total Tests with   1 Free Tests
Start Free Test
Suggested Exams
Exam-Logo
UPSC IES

UPSC IES Important Links

More Communication Systems Questions

Q1.Which of the following components is required to detect (demodulate) Pulse Position Modulation (PPM)? a) Pulse Generator b) RS Flip-Flop c) PWM Demodulator
Q2.Which of the following statements about the AM detection using PLL circuit is/are correct? S1: It has higher noise immunity than the conventional peak detector type AM detector. S2: The PLL is locked to the carrier frequency of the AM signal.
Q3.In a 100% modulated AM signal with a carrier power of 100 W, what is the power in the lower sideband?
Q4.Which of the following is NOT a commonly used pulse-shaping filter in communication systems?
Q5.In which modulation technique is the carrier modulated using phase shifts of 0°, 90°, 180°, and 270°?
Q6.What is another name for PWM in communication engineering?
Q7.Which of the following statements about FM detection using PLL circuit are correct? S1: At the error amplifier output, we get demodulated FM output. S2: FM signal is applied to the input of the PLL.
Q8.In PLL as frequency synthesizer, if the crystal oscillator having frequency 500 MHz is passed through divide by 2 network, then the input frequency to PLL is _______ MHz.
Q9.The following block diagram represents which type of signal generation in communication?
Q10.What is a primary application of VSB (Vestigial Sideband) modulation?
Important Exams
Super Coaching
Exams
Test Series
Previous Year Papers
Objective Questions
Testbook USA SAT Exam
Testbook USA ACT Exam
US College Admissions Guide
Testbook Edu Solutions Pvt. Ltd.
1st & 2nd Floor, Zion Building,
Plot No. 273, Sector 10, Kharghar,
Navi Mumbai - 410210
[email protected]
Toll Free:1800 833 0800
Office Hours: 10 AM to 7 PM (all 7 days)
Company
About usCareers We are hiringTeach Online on TestbookPartnersMediaSitemap
Products
Test SeriesTestbook PassOnline CoursesOnline VideosPracticeBlogRefer & EarnBooks
Our Apps
Follow us on
Copyright © 2014-2022 Testbook Edu Solutions Pvt. Ltd.: All rights reserved
User PolicyTermsPrivacy
Get Free Access Now
Hot Links： teen patti 3a teen patti wink all teen patti master teen patti wala game